Launch Creader CRP129X OBD2 Tool Code Reader 4 System with Oil/EPB/SAS/TPMS
For Engine System: The diagnostic tool can help detect the engine ignition, fuel injection, air and fuel ratio, and exhaust emission conditions in Engine system to enhance vehicle performance, save energy and reduce exhaust emission.
For Transmission: It makes great sense in the safe driving when your car is slipping or difficult to shift. This diagnostic scanner can figure the problems out via reading codes in the Transmission system, or check the health status via live data viewing.
For ABS System: Diagnosing an ABS problem should always start with a visual inspection of all brake components, next you will need to retrieve ABS codes to tell you where the problem is, and this is what this scanner does for you.
For SRS System: SRS, safety restraint system, is made up of impact sensors, a control module, and the airbags themselves, and this diagnostic device can detect every electronic parameter to check its health status.
The LAUNCH OBD2 diagnostic scan tool CRP129X has been made to work effectively with 5 most commonly used services accessible for complete diagnoses and maintenance:
Oil Reset: It is also enabled with an oil service and lamp reset mechanism, a function which ensures that the vehicle engine is maintained in its rightful healthy self.
SAS Reset: It helps clear the faulty steering angle sensor memories and plays an important role in the steering angle sensor calibration.
EPB Service: Reset the brake pad after the repairs in electronic parking brake system are done. By using this system, the braking process is therefore made much simpler and easier.
TPMS Service: Looks up the tire sensor IDs from the vehicles ECU, and performs TPMS programming and reset procedures after tire sensors are replaced.
Throttle Adaptation: Initialize the throttle actuators to the default state for regulating throttle (or idle engine) operations accurately.
They are sufficient to assure the user of the high quality standards the product has been taken through.
AutoVIN Technology Available for Efficient Analysis
The diagnostic tool equips with the AutoVIN technology which means that it will automatically read and store your vehicles VIN number, in one touch. It immediately identifies your car, and you don't have to enter the year, make, engine, etc. of your car.
This will allow you:
Firstly, you can automatically identify the vehicle and perform a quick scan, to easily read and retrieve diagnostic trouble codes related.
Secondly, you can quickly match the right software that will enhance the diagnostic capabilities and resolve compatibility issues. AutoVIN retrieval plays an important role when choosing the correct firmware when performing an update.
Besides, being able to retrieve VIN will help you to easily track the previous records of a vehicle. The records will show the performance of the vehicle and other important aspects such as mileage. As a result, you will be able to make a more informed choice when purchasing a used car.
Automatic Inspection Report Uploaded for Convenience
There might arise certain problems which would be beyond your level of understanding while diagnosing a vehicle. LAUNCH CRP129X allows you to save the Inspection Report and transfer the report to the Cloud Server, or even print the data via the PC.
The Inspection Report includes two parts:
Vehicle Information (Year, Make, Model, VIN, Engine Size, Odometer, Vehicle Software Version, Diagnostic Application Version, Diagnostic Path)
Hence, if you would like to make your mechanic understand about the current problem at hand, then you are able to explain it in details. Rather than taking the additional hassle and confusing things, you would easily be able to hand the diagnostics report to anyone concerned. They would take a look at the whole thing and would then understand about what would need to be done.
All Modes of OBDII Functions for Repair Work
This scanner supports all 10 test modes for OBD-II cars which are great for daily repair work. The table below describes the purpose of each mode of operation:
1 - Request Current Powertrain Diagnostic Data
2 - Request Powertrain Freeze Frame Data
3 - Request Emission-Related Diagnostic Trouble Codes
4 - Clear/Reset Emission-Related Diagnostic Information
5 - Request Oxygen Sensor Monitoring Test Results
6 - Request On-Board Monitoring Test Results for Specific Monitored Systems
7 - Request Emission-Related Diagnostic Trouble Codes Detected During Current or Last Completed Driving Cycle
8 - Request Control of On-Board System Test or Component
9 - Request Vehicle Information
10 - Request Emission-Related Diagnostic Trouble Codes with Permanent Status
Wide Coverage of Global Mainstream Vehicle Models
LAUNCH CRP129X has wide compatibility rates with several modes of the OBD2 motor vehicles. The scanner works on pretty much any car made from 2006 and forward, as long as the car has a 16-pin OBD-II port:
Asian:Daewoo, Honda, Hyundai, Kia, Mazda, Mitsubishi, Nissan, Subaru, Suzuki, Toyota, ISUZU
European:Audi, BMW, Smart, VW, Benz, Volvo, Opel, LandRover, SAAB, Seat, Peugeot, Citroen, Skoda, Porsche, Sprinter, Jaguar, Fiat
USA:Ford, GM, Chrysler
In addition, this diagnostic device is also known to support vehicles falling within the controller area network (CAN) category. In this regard, it is said to have the capacity to retrieve both the generic and manufacturer specific codes. Its use is therefore widespread.
If you work on different vehicles regularly, then you really should consider getting this scanner.
Please note that these goods have been imported without the approval of the manufacturer or its licensed supplier. Therefore these goods will not be covered by the warranty of the manufacturer or its licensed supplier.
Yes it is.
Please make sure that you follow below steps:
1/ Download the package from themeforest.net (the file is in zip format)
2/ Extract the file you've just downloaded.
3/ Find this file: ella-3.0.0-sections-ready.zip in the folder Ella Sections Ready 3.0.0, then you just need to upload ella-3.0.0-sections-ready.zip file to your Shopify store.
To save your time and reach our support quickly, please follow below steps:
1/ Create a staff account for us (with Themes permission and Settings permission) http://docs.shopify.com/manual/settings/account/staff-members
2/ Capture screenshot or video for the issue you get.
3/ Specify which template and version you are using.
4/ Describe clearly how to reproduce the issue.
5/ Send all information (staff account, screenshot, video, template name and version, description of the issues, link) to firstname.lastname@example.org
Yes, we will assist you to install the template if needed
Yes, we do. Please send your customisation requests to email@example.com, we will give you our quote. Thank you.
Yes. You can turn on/off the animation in the Setting page.
Yes. You can turn on/off almost any blocks on the page (featured products, slideshow, banners, related products, recent products,...).
Yes, we have a setting for you to switch between these two options: Display on Hover and Display on Click.
The theme package includes theme source, Photoshop design files, sample data and manual guide.
That is not a problem. You just need to modify the width/height ratio in theme settings.